《电子技术应用》
您所在的位置:首页 > EDA与制造 > 设计应用 > SiC深沟槽ICP刻蚀轮廓质量协同调控与工艺适配研究
SiC深沟槽ICP刻蚀轮廓质量协同调控与工艺适配研究
集成电路应用
郭海生
同济大学电子与信息工程学院
摘要: 为解决SiC深沟槽ICP刻蚀中刻蚀速率、侧壁角、选择比及片内一致性难以协同优化的问题,该文基于常规沟槽、超结结构及贴假片样片的截面SEM结果与同批次工艺记录,建立轮廓质量协同评价体系。结果表明,O2比例由6%增至12%时,侧壁角由82.5°提高至85.8°,选择比由5.2提高至7.2,中心-边缘差异由12%降至7%;SF6流量由30 cm3/min增至80 cm3/min时,刻蚀速率由0.18 μm/min提高至0.32 μm/min,选择比由7.5降至5.1。对88 mTorr、200 mTorr、300 mTorr和400 mTorr四组压力(1 mTorr≈0.133 Pa)进行比较后发现,200~300 mTorr能够在刻蚀速率、选择比与底部形貌之间取得较好平衡,其中200 mTorr未观察到底部残留,300 mTorr仅出现轻微残留,而400 mTorr出现明显残留。超结沟槽对底部残留、有效选择比和回填适配性更为敏感,贴假片工况会增大中心-边缘差异并降低侧壁质量。基于上述规律形成的工艺窗口重构方法可用于同一设备平台、相近掩膜体系和相似图形尺度下的工艺迁移与参数补偿。
中图分类号:TN305.7文献标识码:ADOI:10.19339/j.issn.1674-2583.2026.09.003
中文引用格式:郭海生. SiC深沟槽ICP刻蚀轮廓质量协同调控与工艺适配研究[J].集成电路应用,2026,43(9):13-19.
英文引用格式:Guo Haisheng. Research on the coordinated control of contour quality and process adaptation for SiC deeptrench ICP etching[J].Application of IC,2026,43(9):13-19.
Research on the coordinated control of contour quality and process adaptation for SiC deeptrench ICP etching
Guo Haisheng
School of Electronic and Information Engineering, Tongji University
Abstract: To achieve coordinated optimization of the etch rate, sidewall angle, selectivity, and within-wafer uniformity in silicon carbide (SiC) deep-trench inductively coupled plasma (ICP) etching, this study establishes a profile-quality evaluation framework using cross-sectional SEM results and process records from matched experimental batches. The results demonstrated that the O2 ratio increased from 6% to 12%, the sidewall angle from 82.5° to 85.8° and the selectivity from 5.2 to 7.2, while reducing the center-to-edge difference from 12% to 7%.
Key words : SiC; deep trench; ICP etching; profile quality; process adaptation

引言



本文详细内容请下载:

http://www.chinaaet.com/resource/share/2000007326


投稿邮箱:ICAPP@belling.com.cn


作者信息:

郭海生

(同济大学电子与信息工程学院,上海201800)

2.jpg

此内容为AET网站原创,未经授权禁止转载。